MD Helicopters 369-500, Инструкция по техническому обслуживанию

Страница: 574 / 722

CSP-HMI-3
MD Helicopters, Inc
.
MAINTENANCE MANUAL
[ Main Menu ]
[ HMI − 3 Book TOC ]
[ Chapter 96 TOC ]
Page 906
Revision 11
96-45-00
The information disclosed herein is proprietary to MD Helicopters, Inc.
Neither this document nor any part hereof may be reproduced or transferred to
other documents or used or disclosed to others for manufacturing or any other
purpose except as specifically authorized in writing by MD Helicopters, Inc.
Copyright
©
1999 − 2016 by MD Helicopters, Inc.
Consumable Materials
(Ref. Section 91 − 00 − 00)
Item Nomenclature
CM614 Sleeving, heat-shrink
CM703 Tie strap
CM815 Solder
(1). Attach terminals to wire No. K510F16;
then connect wire to circuit breaker
terminal CB 128-1 and key switch
terminal S3-2.
(2). Attach terminal to one end of jumper
wire; then connect wire with terminal
to circuit breaker terminal CB128-2.
Attach other end of wire to caution
light terminal XDS11-1 and secure
with solder (CM815).
(3). Attach wire No. L562B20 to caution
light terminal XDS11-2l and secure
with solder (CM815). Attach splice
SP67-A to other end of wire for
eventual connection to searchlight
wiring.
(4). Attach terminal to wire No. L564B20;
then connect wire with terminal to
circuit breaker terminal CB128-2.
Attach splice SP66-A to other end of
wire for eventual connection to search­
light wiring.
(5). Attach terminal to wire No. L565A20N;
then connect wire with terminal to
ground stud E3. Attach other end of
wire to caution light terminal XDS11-3
and secure with solder (CM815).
(6). Attach terminal to wire No. P506AE10
and connect wire with terminal to bus
W3-4. Attach terminal to other end of
wire and connect wire with terminal to
circuit breaker terminal CB127-1.
(7). Attach terminal to wire No. L557A10;
and connect wire, with terminal, to
circuit breaker terminal CB127-2.
Attach terminal to other end of wire;
then connect wire with terminal to
relay terminal K302-A1.
NOTE:
Steps (8). thru (10). provide for wiring
installations between the relays and the
relay ground, and wiring from the search­
light assembly (Ref. Figure 202).
(8). Attach terminals on three jumper
wires; then connect one wire with
terminals to relay terminals K302-X1
and K303-X1. Connect second wire
with terminals to relay terminals
K302-X2 and K303-X2. Connect
remaining wire with terminals to relay
terminals K302-A1 and K303-A1.
(9). Attach terminal to jumper wire; and
connect wire with terminal to relay
terminal K303-X2. Attach terminal to
other end of wire; and connect wire
with terminal to E27 ground stud.
(10). Connect wiring from searchlight
assembly as follows:
(a). If required, attach splice SP66-B to
wire No. L564A16 (yellow wire from
5205-1). Connect yellow wire with
splice to splice SP66-A (on wire from
circuit breaker).
(b). If required, attach splice SP67-B to
wire No. L562A20 (white wire from
S206-2). Connect white wire with
splice to splice SP67-A (on wire from
caution light).
(c). If required attach terminal to wire
No. L510G20 (white wire from
S206-1). Connect white wire with
splice to E27 ground stud.
(d). If required, attach terminal to wire
No. L563A16 (yellow wire from
S205-2). Connect yellow wire with
terminal to relay terminal K302-X1.
(e). If required, attach terminals to red
and green wires from lamps (red wire
from DS401-2 and green wire from
DS402-2). Connect green and red
wires with terminals to E27 ground
stud.
NOTE:
If required, terminals are used on ends
of red and green wires at lamp terminals
DS401-2 and DS402-2.