LevelOne IES-0883 Скачать руководство пользователя

Страница: 92 / 152

IES-0883 User Manual

Page 91

Example:

The following example shows setting

storm-control level

LEVEL (

) to the interface fe1

(port 1):

switch_a(config)#interface fe1

switch_a(config-if)#storm-control level 30

switch_a(config-if)#

Broadcast:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

storm-control broadcast enable

command to enable broadcast traffic.

Use

no storm-control broadcast

command to disable broadcast traffic.

Command Syntax:

storm-control broadcast enable

no storm-control broadcast

Example:

The following example shows setting

storm-control broadcast enable

to the interface

fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control broadcast enable

switch_a(config-if)#

Multicast:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

storm-control multicast enable

command to enable multicast traffic.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды