LevelOne IES-0883 Скачать руководство пользователя

Страница: 95 / 152

IES-0883 User Manual

Page 94

Port Mirroring

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use this command to define a mirror source port and its direction.
Use the no parameter with this command to disable port mirroring by the destination port

on the specified source port.

Command Syntax:

mirror interface SOURCEPORT direction SNOOPDIRECTION
no mirror interface SOURCEPORT

SOURCEPORT Name of the Source interface to be used.

SNOOPDIRECTION [both|receive|transmit]

both Specifies mirroring of traffic in both directions.

receive Specifies mirroring of received traffic.
transmit Specifies mirroring of transmitted traffic.

Example:

The following example enables port mirroring by the destination port fe1 (port 1) on the

specified source port fe2 (port 2):

switch_a(config)#interface fe1

switch_a(config-if)#mirror interface fe2 direction both

switch_a(config-if)#

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды