LevelOne IES-0883 Скачать руководство пользователя

Страница: 110 / 152

IES-0883 User Manual

Page 109

VLAN

VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based

VLAN

802.1Q VLAN Setting

VLAN Database:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

vlan database

command to enter the VLAN configuration mode.

Command Syntax:

vlan database

Example:

The following example changes to VLAN configuration mode from Configure mode:

switch_a(config)#vlan database

switch_a(config-vlan)#

Add VLAN/Delete VLAN:

Command Mode: VLAN Configure mode

Logon to Configure Mode (Configure Terminal Mode).
Logon to VLAN Configure Mode.
The

switch_a(config-vlan)#

prompt will show on the screen.

switch_a(config)#vlan database

switch_a(config-vlan)#

Usage:

This command enables or disables the state of a p articular VLAN on a b ridge basis.

Specifying the disable state causes all forwarding over the specified VLAN ID on the

specified bridge to cease. Specifying the enable state allows forwarding of frames on the

specified VLAN-aware bridge.

Command Syntax:

vlan VLANID bridge GROUP name VLAN_NAME state enable/disable

no vlan VLANID bridge GROUP

VLANID The VID of the VLAN that will be enabled or disabled on the bridge <2-4094>.
GROUP <1-1> The ID of the bridge-group on which the VLAN will be affected.

VLAN_NAME The ASCII name of the VLAN. Maximum length: 16 characters.

enable Sets VLAN into an enable state.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды