LevelOne IES-0883 Скачать руководство пользователя

Страница: 112 / 152

IES-0883 User Manual

Page 111

Usage:

Use

switchport mode hybrid

command to set the switching characteristics of the Layer-2

interface as hybrid, and classify both tagged and untagged frames.
Use the

no switchport hybrid

command to reset the mode of the Layer-2 interface to

access (default).

Command Syntax:

switchport mode hybrid

switchport mode hybrid acceptable-frame-type all/vlan-tagged

no switchport hybrid

all Set all frames can be received.
vlan-tagged Set vlan-tagged frames can only be received.

Example:

The following example sets the

switchport mode hybrid

of the interface fe1 (port 1) and

all frames to be received on interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#switchport mode hybrid acceptable-frame-type all

switch_a(config-if)#

Switchport mode trunk:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

switchport mode trunk

command to set the switching characteristics of the Layer-2

interface as trunk, and specify only tagged frames.

Use the

no switchport trunk

command to reset the mode of the Layer-2 interface to

access (default).

Command Syntax:

switchport mode trunk
no switchport trunk

Example:

The following example sets the

switchport mode trunk

of the interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if)#switchport mode trunk

switch_a(config-if)#

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды