LevelOne IES-0883 Скачать руководство пользователя

Страница: 93 / 152

IES-0883 User Manual

Page 92

Use

no storm-control multicast

command to disable multicast traffic.

Command Syntax:

storm-control multicast enable
no storm-control multicast

Example:

The following example shows setting

storm-control multicast enable

to the interface fe1

(port 1):

switch_a(config)#interface fe1
switch_a(config-if)#storm-control multicast enable

switch_a(config-if)#

DLF:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

storm-control dlf enable

command to enable destination lookup failure traffic.

Use

no storm-control dlf

command to disable destination lookup failure traffic.

Command Syntax:

storm-control dlf enable

no storm-control dlf

dlf destination lookup failure

Example:

The following example shows setting

storm-control dlf enable

to the interface fe1 (port

1):

switch_a(config)#interface fe1

switch_a(config-if)#storm-control dlf enable
switch_a(config-if)#

Static MAC Entry

Static-MAC-Entry Forward:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды