LevelOne IES-0883 Скачать руководство пользователя

Страница: 91 / 152

IES-0883 User Manual

Page 90

Switching

Bridging, Static MAC Entry, Port Mirroring

Bridging

Aging Time (seconds):

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use this command to specify an ageing-out time for a learned MAC address. The learned
MAC address will persist till this specified time.

Command Syntax:

Bridge GROUP ageing-time AGEINGTIME

no bridge GROUP ageing-time

Group = <1-1> The ID of the bridge-group that this ageing time is for.

AGEINGTIME = <10-1000000> The number of seconds of persistence.

Example:

The following example sets the new AGEINGTIME (

1000

) to bridge GROUP (

switch_a(config)#bridge 1 ageing-time 1000
switch_a(config)#

Threshold level (0-100):

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

storm-control level

command to specify the rising threshold level for broadcasting,

multicast, or destination lookup failure traffic. The storm control action occurs when traffic
utilization reaches this level.

Command Syntax:

storm-control level LEVEL

LEVEL <0-100> specifies the percentage of the threshold; percentage of the maximum
speed (pps) of the interface.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды