LevelOne IES-0883 Скачать руководство пользователя страница 27

Страница: 27 / 152

IES-0883 User Manual

Page 26

WARM START
COLD START
LINK UP
LINK DOWN
AUTHENTICATION FAILURE
RISING ALARM
FALLING ALARM
TOPOLOGY ALARM

MIB-II defines a set of manageable objects in various layers of the TCP/IP protocol suites.

MIB-II covers all manageable objects from layer 1 to layer 4, and, as a result, is the major

SNMP MIB supported by all vendors in the networking industry. The switch supports a

complete implementation of SNMP Agent and MIB-II.

RMON MIB (RFC 2819) and Bridge MIB (RFC 1493)

The switch provides hardware-based RMON counters in the switch chipset. The switch

manager CPU polls these counters periodically to collect the statistics in a format that

complies with the RMON MIB definition.

RMON Groups Supported

The switch supports the following RMON MIB groups defined in RFC 2819:

RMON Statistics Group – maintains utilization and error statistics for the

switch port being monitored.

RMON History Group – gathers and stores periodic statistical samples from

the previous Statistics Group.

RMON Alarm Group – allows a network administrator to define alarm

thresholds for any MIB variable. An alarm can be associated with Low

Threshold, High Threshold, or both. A trigger can trigger an alarm when the

value of a specific MIB variable exceeds a threshold, falls below a threshold,

or exceeds or falls below a threshold.

RMON Event Group – allows a network administrator to define actions

based on alarms. SNMP Traps are generated when RMON Alarms are

triggered. The action taken in the Network Management Station depends on
the specific network management application.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды