LevelOne IES-0883 Скачать руководство пользователя

Страница: 78 / 152

IES-0883 User Manual

Page 77

System

System Information, System Name/Password, IP Address, Save Configuration,

Firmware Upgrade, Reboot, Logout

System Name/Password

System Name:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

hostname

command to set or change the network server name.

Use the

no hostname

command to disable this function.

Command Syntax:

(no) hostname HOSTNAME

HOSTNAME specifies the network name of the system.

Example:

The following example sets the hostname to

switch

, and shows the change in the prompt:

switch_a(config)#hostname switch
switch(config)#

Password:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды