LevelOne IES-0883 Скачать руководство пользователя

Страница: 28 / 152

IES-0883 User Manual

Page 27

Bridge Groups Supported

The switch supports the following four groups of Bridge MIB (RFC 1493):

The dot1dBase Group – a mandatory group that contains the objects

applicable to all types of bridges.

The dot1dStp Group – contains objects that denote the bridge’s state with

respect to the Spanning Tree Protocol. If a node does not implement the

Spanning Tree Protocol, this group will not be implemented. This group is

applicable to any transparent only, source route, or SRT bridge that

implements the Spanning Tree Protocol.

The dot1dTp Group – contains objects that describe the entity’s transparent

bridging status. This group is applicable to transparent operation only and

SRT bridges.

The dot1dStatic Group – contains objects that describe the entity’s

destination-address filtering status. This group is applicable to any type of

bridge which performs destination-address filtering.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды