LevelOne IES-0883 Скачать руководство пользователя

Страница: 136 / 152

IES-0883 User Manual

Page 135

(VLAN) when no multicast routing protocol is configured in the subnet (VLAN). When

enabled, the IGMP Snooping querier sends out periodic IGMP queries for all interfaces on

that VLAN.
Use the

no ip igmp snooping querier

command to disable IGMP querier configuration.

Command Syntax:

(no) ip igmp snooping querier

Example:

The following example enables IGMP snooping querier:

switch_a(config)# ip igmp snooping querier

switch_a(config)#

IGMP mode:

Passive:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

ip igmp snooping

command to enable IGMP Snooping. This command is given in the

Global Config mode. IGMP Snooping is enabled at the switch level.
Use the

no ip igmp snooping

command to globally disable IGMP Snooping.

Command Syntax:

(no) ip igmp snooping enable

Example:

The following example enables IGMP snooping on the switch:

switch_a(config)# ip igmp snooping enable

switch_a(config)#

IGMP version:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

vlan1.1 means vlan 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface vlan1.1

switch_a(config-if)#

Usage:

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды