LevelOne IES-0883 Скачать руководство пользователя

Страница: 111 / 152

IES-0883 User Manual

Page 110

disable Sets VLAN into a disable state.

Example:

The following example enables the vlan VLANID (

) and name VLAN_NAME (

vlan2

) of

bridge GROUP (

switch_a(config-vlan)#vlan 2 bridge 1 name vlan2 state enable

switch_a(config-vlan)#

802.1Q Port Setting

Switchport mode access:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

switchport mode access

command to set the switching characteristics of the Layer-2

interface to access mode, and classify untagged frames only.
Use the

no switchport access

command to reset the mode of the Layer-2 interface to

access (default).

Command Syntax:

switchport mode access

no switchport access

Example:

The following example sets the

switchport mode access

of the interface fe1 (port 1):

switch_a(config)#interface fe1

switch_a(config-if)#switchport mode access

switch_a(config-if)#

Switchport mode hybrid:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды