LevelOne IES-0883 Скачать руководство пользователя

Страница: 22 / 152

IES-0883 User Manual

Page 21

Switch Management

This chapter explains the methods that you can use to configure management access to
the switch. It describes the types of management applications and the communication

and management protocols that deliver data between your management device

(workstation or personal computer) and the system. It also contains information about

port connection options.

This chapter covers the following topics:

•

Management Access Overview

•

Key Concepts

•

Key Guidelines for Implementation

•

Web Management Access

•

Administration Console Access

•

SNMP Access

•

Standards, Protocols, and Related Reading

Management Access Overview

The switch gives you the flexibility to access and manage the switch using any or all of the

following methods.

The web browser interface and administration console (CLI) support are embedded in the
switch software and are available for immediate use.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды