LevelOne IES-0883 Скачать руководство пользователя

Страница: 35 / 152

IES-0883 User Manual

Page 34

Firmware Upgrade

Filename: Click in “Filename” text box and type the name of the file that you intend to

upgrade it to the switch.

TFTP server IP: Click in “TFTP server IP” text box and type the TFTP server IP address

from where the file will be obtained.

Upgrade: Click “upgrade” button to upgrade firmware to the switch. Please follow the

message on the screen during the firmware upgrade process. Do not turn off the

power or perform other functions during this period of time. Reboot the switch after
completing the upgrade process.

Please follow the message on the screen during the firmware upgrade process. Do not

turn off the power or perform other functions during this period of time.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды