LevelOne IES-0883 Скачать руководство пользователя

Страница: 140 / 152

IES-0883 User Manual

Page 139

Usage:

Use

ip igmp snooping report-suppression

command to enable report suppression for

IGMP versions 1 and 2.
Use the

no ip igmp snooping report-suppression

command to disable report

suppression.

Command Syntax:

(no) ip igmp snooping report-suppression

Example:

The following example enables report suppression for IGMPv2 reports on

vlan1.1

switch_a(config)#interface vlan1.1

switch_a(config-if)#ip igmp version 2

switch_a(config-if)#ip igmp snooping report-suppression

switch_a(config-if)#

NTP

NTP Status:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

ntp enable

command to enable NTP for the Switch.

Use

no ntp enable

command to disable NTP for the Switch.

Command Syntax:

(no) ntp enable

Example:

The following example enables NTP for the Switch:

switch_a(config)#ntp enable

switch_a(config)#

NTP Server:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды