LevelOne IES-0883 Скачать руководство пользователя

Страница: 113 / 152

IES-0883 User Manual

Page 112

Switchport hybrid allowed vlan:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if)#

Usage:

Use this command to set the switching characteristics of the Layer-2 interface to hybrid.
Both tagged and untagged frames will be classified over hybrid interfaces.

Use the no parameter to turn off allowed hybrid switching.

Command Syntax:

switchport hybrid allowed vlan all
switchport hybrid allowed vlan none

switchport hybrid allowed vlan add VLANID egress-tagged enable/disable

switchport hybrid allowed vlan remove VLANID

no switchport hybrid vlan

all Allow all VLANs to transmit and receive through the Layer-2 interface.
none Allow no VLANs to transmit and receive through the Layer-2 interface.

add Add a VLAN to the member set.

remove Remove a VLAN from the member set.

VLANID <2-4094> The ID of the VLAN or VLANs that will be added to, or removed from,

the Layer-2 interface.

For a VLAN range, specify two VLAN numbers: lowest, then highest number in the range,

separated by a hyphen.

For a VLAN list, specify the VLAN numbers separated by commas.

egress-tagged

enable Enable the egress tagging for the outgoing frames.
disable Disable the egress tagging for the outgoing frames.

Example:

The following example specifies to

add

the interface fe1 (port 1) to VLANID (

) and

enable

the

egress-tagged

for the outgoing frames on interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if )#switchport hybrid allowed vlan add 2 egress-tagged enable
switch_a(config-if )#

Switchport trunk allowed vlan:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

fe1 means port 1.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды