LevelOne IES-0883 Скачать руководство пользователя

Страница: 138 / 152

IES-0883 User Manual

Page 137

Then logon to Interface mode.

vlan1.1 means vlan 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface vlan1.1
switch_a(config-if)#

Usage:

Use

ip igmp query-interval

command to configure the frequency of sending IGMP host

query messages.
To return to the default frequency, use the

no ip igmp query-interval

command.

Command Syntax:

ip igmp query-interval INTERVAL

no ip igmp query-interval

INTERVAL <1-18000> Frequency (in seconds) at which IGMP host query messages are

sent. Default: 125 seconds.

Example:

The following example changes the frequency of sending IGMP host-query messages to 2
minutes on

vlan1.1

switch_a(config)#interface vlan1.1
switch_a(config-if)#ip igmp query-interval 120

switch_a(config-if)#

IGMP querier:

Max-response-time:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.
vlan1.1 means vlan 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface vlan1.1

switch_a(config-if)#

Usage:

Use

ip igmp query-max-response-time

command to configure the maximum response

time advertised in IGMP queries.

To restore to the default value, use the

no ip igmp query-max-response-time

command.

Command Syntax:

ip igmp query-max-response-time RESPONSETIME

no ip igmp query-max-response-time

RESPONSETIME <1-240> Maximum response time (in seconds) advertised in IGMP

queries. Default: 10 seconds.

Содержание IES-0883

























































































































































Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды

LevelOne IES-0883, Руководство пользователя

Результаты поиска

Содержание IES-0883

Отзывы:

Похожие инструкции для IES-0883

Бренды по названию

Популярные бренды