Lenovo Flex System x220 Скачать руководство пользователя страница 78

Страница: 78 / 714

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

089-804-000 : CPU Stress Test Aborted

CPU Stress Test Aborted. User pressed Ctrl-C.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

089-901-000 : CPU Stress Test Failed

CPU Stress Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system and then run the test again.

2. Make sure that the DSA Diagnostic code is at the latest level.

3. Run the test again.

4. Check system firmware level and upgrade if necessary. The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

5. Run the test again.

6. If the system has stopped responding, turn off and restart the system and then run the test again.

7. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Flex System x220 Compute Node Installation and Service Guide

Содержание Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Flex System x220

Отзывы:

Похожие инструкции для Flex System x220

Бренды по названию

Популярные бренды

Lenovo Flex System x220, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Flex System x220

Отзывы:

Похожие инструкции для Flex System x220

Бренды по названию

Популярные бренды