Lenovo Flex System x220 Скачать руководство пользователя страница 616

Страница: 616 / 714

•

W.305800C [W.305800C] DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required

Controller.

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller

Severity

Warning

User Response

Complete the following steps:

Reboot the system.

2. If problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace system board.

Related links

–

“Updating firmware and device drivers” on page 21

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

W.305800D [W.305800D] DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires

'Reboot'.

Explanation:

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'

Severity

Warning

User Response

Complete the following steps:

1. Reboot the system to reconnect the controller.

2. If problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

Related links

–

“Updating firmware and device drivers” on page 21

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

W.305800E [W.305800E] DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.

Explanation:

DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver

Severity

Warning

User Response

Complete the following steps:

Reboot the system.

2. If problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

608

Flex System x220 Compute Node Installation and Service Guide

Содержание Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Flex System x220

Отзывы:

Похожие инструкции для Flex System x220

Бренды по названию

Популярные бренды

Lenovo Flex System x220, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Flex System x220

Отзывы:

Похожие инструкции для Flex System x220

Бренды по названию

Популярные бренды