Lenovo Flex System x220 Скачать руководство пользователя страница 672 | Manualshive

Страница: 672 / 714

background image

additional drive in hard disk drive bay 1. The compute node supports using RAID 0 or RAID 1 when two
hard disk drives of the same interface type are installed. See “Configuring a RAID array” on page 33 for
information about RAID configuration.

To install a hot-swap hard disk drive or hard disk drive bay filler, complete the following steps.

0000

0000

0000

0000

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

Release
latch

Hard disk
drive
assembly

Hard disk
drive bay filler

Drive
handle

Activity
LED
(green)

Error
LED
(amber)

Step 1.

Identify the hard disk drive bay (hard disk drive bay 0 or hard disk drive bay 1) in which you plan to
install the hot-swap hard disk drive.

Step 2.

If a hard disk drive bay filler is installed, remove it from the compute node by pulling the release
lever and sliding the filler away from the compute node.

Step 3.

Touch the static-protective package that contains the hot-swap hard disk drive to any

unpainted

metal surface on the Flex System chassis or any

unpainted

metal surface on any other grounded

rack component; then, remove the drive from the package.

Step 4.

Open the release lever on the drive and slide the drive into the bay until it is firmly seated in the
connector.

Step 5.

Lock the drive into place by closing the release lever.

Step 6.

Check the hard disk drive status LEDs to make sure that the drive is operating correctly.

See “Configuring a RAID array” on page 33 for information about SAS RAID configuration.

Removing a ServeRAID controller

Use this information to remove a ServeRAID controller.

When the ServeRAID controller is removed, software RAID is not supported. The compute node does not
support downgrading to the software RAID function from the hardware RAID configuration.

Before you remove the ServeRAID controller, complete the following steps:

1. Read “Safety” on page iii and “Installation guidelines” on page 637.

2. If the compute node is installed in an Flex System chassis, remove it (see “Removing a compute node

from a chassis” on page 639 for instructions).

3. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with

the bezel pointing toward you.

664

Flex System x220 Compute Node Installation and Service Guide

«
...
670
671
672
673
674
...
»

Содержание Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex System x220

BladeCenter HS23

Бренд: IBM Страницы: 36

UniServer BT716F

Бренд: H3C Страницы: 44

Бренд: Hawking Страницы: 40

Eserver 345 Series

Бренд: IBM Страницы: 70

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

Sooloos Ensemble

Бренд: Meridian Страницы: 2

Device Installer

Бренд: Lantronix Страницы: 21

Device Server MSS 485

Бренд: Lantronix Страницы: 69

Бренд: Lanner Страницы: 72

Бренд: Kontron Страницы: 42

Бренд: hopf Elektronik GmbH Страницы: 178

Бренд: SAFARI Montage Страницы: 5

LANTIME M300/MGR

Бренд: Meinberg Страницы: 5

Бренд: QSSC Страницы: 97

Бренд: TAG Страницы: 84

Бренд: 3onedata Страницы: 3

UniServer 1522LV

Бренд: Uniwide Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды