Lenovo Flex System x220 Скачать руководство пользователя страница 609 | Manualshive

Страница: 609 / 714

background image

User Response

Complete the following steps:

1. Continue booting the system. If the system does not reset, manually reset the system.

2. If the error is not reported on the subsequent boot, no additional recovery action is required.

3. If the error persists, continue booting system and update the UEFI image.

4.

Replace the system board.

Related links

–

“Updating firmware and device drivers” on page 21

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

S.3818007 [S.3818007] The firmware image capsules for both flash banks could not be verified.

Explanation:

CRTM image capsule could not be verified

Severity

Error

User Response

Complete the following steps:

1. If system failed to boot successfully, DC cycle system.

2. If system boots to F1 setup, update the UEFI image and reset bank to primary (if required). If the

system boots without error, recovery is complete and no additional action is required.

3. If system fails to boot, or if the firmware update attempt fails, replace the system board.

Related links

–

“Updating firmware and device drivers” on page 21

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

S.51003 [S.51003] An uncorrectable memory error was detected in DIMM slot % on rank %.

Explanation:

[S.51003] An uncorrectable memory error was detected on processor % channel %. The

failing DIMM within the channel could not be determined.[S.51003] An uncorrectable memory error has
been detected during POST. Fatal Memory Error Occurred

Severity

Error

User Response

Complete the following steps:

1. Prior to replacing memory DIMM, refer to TIP H212154 for minimum code level.

2. If the compute node has recently been installed, moved, serviced, or upgraded, verify that

the DIMM is properly seated and visually verify that there is no foreign material in any DIMM
connector on that memory channel. If either of these conditions is found, correct and retry with
the same DIMM. (Note: The event Log might contain a recent 00580A4 event denoting detected
change in DIMM population that could be related to this problem.)

Troubleshooting

601

«
...
607
608
609
610
611
...
»

Содержание Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex System x220

Бренд: Kathrein Страницы: 16

Бренд: 3onedata Страницы: 4

Бренд: Vitek Страницы: 2

Бренд: IBM Страницы: 200

SuperWorkstation 740A-T

Бренд: Supermicro Страницы: 138

BladeCenter HS20 Type 8843

Бренд: IBM Страницы: 112

Бренд: Intermec Страницы: 232

Бренд: Black Box Страницы: 30

TERASTATION HS-D1.0TGL/R5

Бренд: Buffalo Страницы: 2

WPS54GU2 - Wireless-G PrintServer For USB 2.0 Print Server

Бренд: Linksys Страницы: 76

WPSM54G - Wireless-G PrintServer With Multifunction Printer Support Print Server

Бренд: Linksys Страницы: 132

Бренд: IBM Страницы: 58

System x3500 M4

Бренд: IBM Страницы: 170

Бренд: Planet Страницы: 141

Бренд: R/Evolution Страницы: 130

Бренд: Lantronix Страницы: 2

Бренд: Gateway Страницы: 60

Бренд: OSS Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды