Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 53 / 135

Preparing for use

OptiCut 23

HydroProtected

Removing the knives

The knife driving shaft can be accessed via the bale chamber. Please

observe the relevant safety instructions »Working in the bale cham-

ber«, page 49.
Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Press the “INFO” button...

> ...until the “Pick-up/Knives” symbol is displayed.

> Press the “GO” button...

> until the “Pick-up/Knives” symbol is selected on the display.

> Swivel the knives in via the control device.

> Open and secure the rear flap.

→

»Opening the rear flap«, page 46.

> Close both ball valves on the hydraulic manifold for the cutterbar

(to do this, open the right-hand side door).

> Release the knife driving shaft locking mechanism.

> Pull the knife driving shaft lever downwards.

> Hold the ends of the knives and pull them out of the knife driving

shaft towards the rear.

OTE

The cutting knives must always be well sharpened. Sharp knives save

energy and guarantee the highest possible quality.

»Sharpening the knives«, page 98

Cutterbar unit

ball valve

Cutterbar hy-

draulic manifold

Lever for the

knife driving shaft

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды