Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 47 / 135

Preparing for use

Adjusting the

roller feelers

The working height of the pick-up equipment is set via the positioning

of the roller feeders, which are locate on both sides of the implement.
The working height specified in the illustration shown is only a recom-

mendation. The correct working height depends on the nature of the

ground and the crop.
Always set the two retainers on the sides of the pick-up equipment to

the same working height.
The roller feelers are adjusted by changing the vertical position of the

support. Adjust as follows:

> Switch the tractor on.

Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Press the “INFO” button...

> ...until the “Pick-up/Knives” symbol is displayed.

> Raise the pick-up equipment via the control device.

Switch off the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Switch off the tractor and secure it.

> Close the ball valve.

> Remove the safety splint.

> Bring both supports to the same working height.

> Attach and secure the safety splint.

> Open the ball valve.

> Switch the tractor on.

Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Lower the pick-up equipment via the control device.

> Check the pick-up equipment setting.

Support sheet

Roller feeler

Safety splint

2 - 3 cm

Open

Closed

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды