Kverneland Vicon RF 2235 Скачать руководство пользователя страница 18

Страница: 18 / 135

Safety

Operation

The implement should not be put into operation for the first time

until the user has been trained to use it.

The implement must not be used until instruction has been given by

distribution company employees, company representatives or manu-

facturer's employees. If initial operation is performed without instruc-

tion, damage to the implement can be caused by operating errors and

accidents can occur.
Ensure that the implement is in perfect working condition.

Do not operate the implement unless it is in perfect working condition.

Check all important components and replace any defective compon-

ents before starting the implement. Defect components can cause da-

mage to equipment and injury to persons.
Check the protective equipment

The protective equipment must not be removed or by-passed. Check

all protective equipment before starting the implement. Unguarded

parts of the implement can cause serious or fatal injuries.
No riding on the implement

Neither personnel nor objects are allowed to be transported on the im-

plement at any time. Riding on the implement is hazardous and strictly

prohibited.
Make sure the immediate vicinity is clear

Check the surrounding area of the implement before starting and con-

tinually during operation. Make sure the operator has an adequate

view of the work area. Only begin work if the immediate vicinity is clea-

red of any persons or objects. There is otherwise the risk of serious or

fatal injury.
Retighten all nuts, bolts and screws

Regularly check that the nuts, bolts and screws are fully tightened and

tighten them, if necessary. Screws can work loose when the imple-

ment is used. The consequence can be damage to the implement and

accidents.
Instructions in the event of malfunctions

In the event of a malfunction, stop, shut down and secure the imple-

ment immediately. The malfunction may be eliminated immediately, or

your dealer must be assigned the task. Using a faulty implement can

cause accidents or damage.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды