Kverneland Vicon RF 2235 Скачать руководство пользователя страница 64

Страница: 64 / 135

Driving on the road

Safety

Before you transport the implement on the road, please read the follo-

wing safety instructions. Compliance is mandatory and will help you in

avoiding accidents.
Observe safety instructions

Observe the safety instructions for the performance of all work. Any

disregard for safety instructions can lead to serious or fatal injuries to

persons.
Always switch off the AutoPlus-Pilotbox when working on the

implement

Always switch off the pilot box when working on the implement. If the

Pilotbox is switched on or starts inadvertently, unforeseen movements

may be triggered on the implement. This can cause accidents with fa-

tal consequences.
Adjusting the load-dependent brake

Before travelling on the road, check that the lever of the implement's

load-dependent brake is adjusted to “Full load”. The braking efficiency

changes. This can cause accidents. The consequence can be traffic

accidents with serious or fatal injuries.
Cleaning the tractor and the implement before road transport

Before any road transport, clean the tractor and implement of any

coarse dirt, remaining crops and clods of earth. Crops or dirt that drop

onto the road can cause slippery road conditions. There is otherwise

the risk of traffic accidents and accidents with fatal consequences.
Close the valves

Close all hydraulic couplings before any transport on public roads. If

the valves are open, then the pick-up equipment may be lowered.

There is otherwise the risk of traffic accidents and accidents with fatal

consequences.
Observe the slewing range

The rear wheel of the tractor should not come into contact with the dra-

wbar when cornering. This may happen during tight turning circles.

Unsuitable driving behaviour can cause serious damage to the imple-

ment.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды