Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 95 / 135

Maintenance

Pick-up equipment

and rotor

OTE

Working with the grease gun

Lubricate the bearings with one or two presses of the grease gun. If

you feel resistance at the second press, do not press a second time.

Too much grease will force the bearings apart. This will allow foreign

bodies to enter the bearing, resulting in premature wear.

Pick-up equipment,

overload coupling,

OptiCut and rotor

Raise the pick-up equipment to the highest position.

> Lubricate the lubrication points.

Rotor cutterbar

> Always lubricate the lubrication points for the cutterbar rotor after

500 bales.

Pick-up equipment

chain wear

The pick-up equipment chain must be replaced when the chain tensio-

ner is just in front of the end stop.

> Measure the pick-up equipment drive chain and replace if neces-

sary.

Lubrication

point

Lubrication

point

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды