Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 34 / 135

Familiarise yourself with the device

AutoPlus control unit messages

Bale density 90%

Indicates that 90% of the set

bale density has been rea-

ched.

A signal sounds to give notifi-

cation.

Bale density 100%

Indicates that the set bale

density has been reached.

A signal sounds to give notifi-

cation.

“Start tying” is displayed. The

tying cycle is running.

The tying cycle was suc-

cessful. Open the rear flap via

the tractor control device. Ob-

serve the safety instructions

for operation.

The bale was ejected. Close

the rear flap via the control de-

vice. Leave the control device

lever in rear flap closed positi-

on for approximately 3 secon-

ds, to build up the pressure

for the default bale density.

Low battery voltage .

The battery voltage is under 9

volts. Check the tractor's po-

wer supply.

A signal sounds to give notifi-

cation.

Twine malfunction

The twine tying does not run.

A signal sounds to give notifi-

cation.

Observe the safety instruc-

tions »Maintenance« on page

86.

Net malfunction

The net tying does not run. A

signal sounds to give notifica-

tion.

Observe the safety instruc-

tions »Maintenance« on page

86.

Net motor malfunction

The net motor does not run.

A signal sounds to give notifi-

cation.

Observe the safety instruc-

tions »Maintenance« on page

86.

The net was drawn in at the

wrong moment.

A signal sounds to give notifi-

cation.

Observe the safety instruc-

tions »Maintenance« on page

86.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды