Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 23 / 135

Familiarise yourself with the device

General

This chapter contains the following information:

•

Range of application and properties

•

Technical specifications

Range of applica-

tion

This implement is a round baler. The implement is solely intended and

designed for the purpose of gathering cut, non-woody or slightly woo-

dy plants, particularly stem crop, from the ground. The gathered crop

is collected together and cut using the cutterbar. The crop is formed

into a round bale in the bale chamber and then wrapped with twine or

net material. This must always take place in compliance with the con-

ditions, instructions, procedures and regulations in this document and

shown in the warning diagrams and safety diagrams on the imple-

ment.

Proper use of the im-

plement

This implement is only designed to be used for agricultural purposes.

Any use whatsoever other than the above mentioned is not proper

use. Neither the manufacturer nor the dealer is liable for any damage

resulting from improper use of the implement. The operator of the im-

plement alone is liable in this case.

Properties

The pick-up equipment takes the crop from the ground and feeds it in-

to the bale chamber. In this process, the crop is also cut by the OptiCut

cutterbar. The bale is uniformly formed by the rotary motion of the rol-

ler systems. The bale expands due to the constant feeding of crop.

When the chosen bale density is achieved, the bale is tied with either

twine or net. The rear flap is opened and the bale is ejected.
Protecting the stubble

The optional load-dependent compressed-air brake for the implement

enables the braking force to be adjusted in direct dependence to the

actual weight in field use. The braking force is manually adjusted in 3

stages. This function protects the stubble.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды