Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 54 / 135

Preparing for use

Fitting the knives

The knife driving shaft can be accessed via the bale chamber. Please

observe the relevant safety instructions in the »Removing the knives«

chapter, page 53.

> When fitting the knives, hold the ends and insert them into the oval

holes on top of the knife driving shaft.

> Ensure that the bale chamber is empty at the end of the work.

> Empty the bale chamber.

> Close the rear flap.

→

»Closing the rear flap«, page 46

Switch off the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Switch off the tractor, take out the ignition key and secure it.

> Push the lever for the knife driving shaft upwards (to do this, open

the right-hand side door).

> Open both ball valves on the hydraulic manifold for the cutterbar (to

do this, open the right-hand side door).

> Switch the tractor on.

Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Press the “INFO” button...

> ...until the “Pick-up/Knives” symbol is displayed.

> Press the “GO” button...

> until the “Pick-up/Knives” symbol is selected on the display.

> Swivel the knives in with the control device.

Lever for the

knife driving shaft

Cutterbar ball

valve

Cutterbar hy-

draulic manifold

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды