Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 70 / 135

Preparations in the field

Safety

Observe safety instructions

Observe the safety instructions for the performance of all work. Any

disregard for safety instructions can lead to serious or fatal injuries to

persons.
Secure the tractor

Before you dismount: Switch off the tractor, take out the ignition key

and secure the tractor against rolling away. An unsecured tractor may

run you over or trap you. There is otherwise the risk of serious or fatal

injury.
Securing the implement

Secure the implement against inadvertent starting and rolling away.

Use wheel chocks. The implement must be standing on firm and level

ground and, if necessary, must be supported during work. Unsecured

or non-supported implements can cause accidents. There is otherwi-

se the risk of serious or fatal injury.
Always switch off the AutoPlus-Pilotbox when working on the

implement

Always switch off the pilot box when working on the implement. If the

Pilotbox is switched on or starts inadvertently, unforeseen movements

may be triggered on the implement. This can cause accidents with fa-

tal consequences.
Do not upset the cardan shaft

The cardan shaft between the tractor and implement must not be jol-

ted in any operating or transport position. Upset cardan shafts can

cause damage to the implement and tractor.
Increases in pressure are prohibited

It is prohibited to increase the maximum working pressure setting for

the bale density on the hydraulic block. Attempting to do so will render

the warranty invalid and exempt the manufacturer from all liability. Da-

mage may be caused to the implement.

General

The implement must be adjusted in the operating position. This is de-

scribed in the following chapter:

•

Baler check list.

•

Adjust the baffle plate.

•

Adjust the bale density.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды