Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 17 / 135

Safety

Road travel

Ensuring road safety

The implement must conform to current national traffic regulations if

you intend to drive it on public roads. Ensure:

•

Lighting, warning and protective equipment is installed and

functioning

•

Compliance with the permissible transport widths and weights, ax-

le loads, tyre loadbearing capacities, laden weights and national

speed restrictions.

•

Compliance with the maximum permissible road transport speed of

40 km/h.

If this is not complied with, the driver and keeper of the vehicle are lia-

ble.
Check the tyre pressure

Check tyre pressure on a regular basis. The wrong tyre pressure will

reduce the service life of a tyre and can cause unstable driving proper-

ties and accidents.
Adjusting the load-dependent brake

Before travelling on the road, check that the lever of the implement's

load-dependent brake is adjusted to “Full load”. The braking efficiency

changes. This can cause accidents. The consequence can be traffic

accidents with serious or fatal injuries.
No riding on the implement

Neither personnel nor objects are allowed to be transported on the im-

plement at any time. Riding on the implement is hazardous and strictly

prohibited.
Altered driving and braking performance

The driving and braking performance are altered when the implement

is attached to the tractor. Take the width and balancing weight of the

implement into consideration, especially when cornering. A driving

style which is not adapted to conditions can cause accidents.
Adapted speed

In the event of bad road conditions and excessive speed, very high

forces can occur that subject the tractor and implement material to

high loads or to an overload. Adapt the speed to the road conditions.

A driving style which is not adapted to conditions can cause accidents.

The consequence can be traffic accidents with serious or fatal injuries.
No bales in the bale chamber

Bales must not be transported in the bale chamber. Transporting ba-

les will affect the steering, braking capability and driving behaviour of

the tractor. Personnel may be injured or the implement may be dama-

ged as a result.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды