Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 15 / 135

Safety

Hitching

Increased risk of injury

When hitching the implement to the tractor, there is an increased risk

of injury. Therefore:

•

secure the tractor in such a way that it cannot roll forwards or back-

wards.

•

Switch off the engine.

•

Remove the ignition key.

•

Never stand between the tractor and the implement during hit-

ching.

•

Mount and secure the implement's cardan shaft to the tractor's

PTO shaft.

Failure to comply may cause damage to the implement and even life-

threatening injuries.
Cardan shaft

Only use a cardan shaft that complies with the manufacturer's speci-

fications. Other cardan shafts with friction clutches require a higher

torque. A higher torque can cause damage to the implement.
Cardan shaft operating manual

Please ensure that you observe the manufacturer's operating manual

for the cardan shaft. This will provide you with information regarding

intended use. Failure to comply can cause damage to the cardan shaft

and to the implement.
Check and attach the protective guard for the cardan shaft

The rotating cardan shaft is protected by a protective guard. Make su-

re that the protective guard for the cardan shaft is not damaged. The

protective guard for the cardan shaft must be attached to the tractor

and the implement by chains. Unsecured cardan shafts can cause se-

rious injuries.
PTO shaft speed 540 rpm

The prescribed maximum PTO shaft speed of 540 rpm must not be ex-

ceeded. A higher PTO shaft speed can cause damage to the imple-

ment.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды