manualshive.com logo in svg

Kverneland Vicon RF 2235, Руководство по эксплуатации

Поделиться
Скачать
Kverneland Vicon RF 2235 Скачать руководство пользователя страница 113

Maintenance

113

Net roller sensor

Check, clean and adjust the net feed roller sensor before the season

and every 500 bales.

Distance (R) must be 4 mm at the sensor.

The sensor is located to the left of the net drive roller.
Adjust the net feed roller sensor as follows:

> Loosen the screws on the sensor mounting.

> Set the sensor to distance R=4 mm.

> Tighten the screws on the sensor mounting.

Twine guide sensor

Check, clean and adjust both twine guide sensors every 3,000 bales.

Distance (G) for the twine guide sensors must be 4 mm.

A star wheel sensor is located on the right-hand star wheel on the twi-

ne carriage (right-hand side door open). The twine carriage sensor is

almost centrally positioned behind the twine carriage.

> Loosen the screws on the sensor mounting.

> Set the distance G between the star wheel sensor and twine car-

riage sensor to 4 mm.

> Tighten the screws on the sensor mounting.

Net roller sensor

Net drive roller

Twine guide sensors

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды