Kverneland Vicon RF 2235 Скачать руководство пользователя страница 103

Страница: 103 / 135

Maintenance

103

Gear box

Check the gearbox oil level:

•

After the first 50 operating hours.

•

At the start of the season.

•

In the case of excess oil loss.

The oil must be changed:

•

After the first 50 operating hours.

•

Every 2 years or

•

after 20,000 bales.

Fill quantity

Checking the oil level correctly

The oil level must only be checked when

•

the implement is at a standstill for any length of time and

•

the implement is horizontal.

Otherwise, an incorrect oil level will be measured. An incorrect oil level

can cause serious damage to the implement.

Checking the oil level

> Remove the level-setting plug.

The filling level is correct when oil runs out.

> Refit the level-setting plug.

If no oil is discharged, the gearbox must be filled with oil.

→

»Filling the gear box«, page 103

Filling the gear box

> Remove the level-setting plug.

> Remove the screw from the filler neck.

> Fill up with gear oil until the filling level indicator is correct.

> Refit the level-setting plug.

> Seal the filler neck again.

Gear-box

Volume (l) Specification

2.3

B 80W90

Level-set-

ting plug

Level-set-

ting plug

Filler plug

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды