Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 76 / 135

Operation

Driving

Maximum cardan shaft speed 540 rpm

The cardan shaft speed must not exceed 540 rpm and has to be ad-

apted to the condition of the crop. Higher speeds can cause damage

to the implement.
Please observe the following instructions when using the implement:

•

The tractor's PTO shaft must be switched on.

•

The working speed should be adjusted to the crop: between 4 and

15 km/h.

Switch on the

tractor's PTO shaft

Only engage the tractor's PTO shaft at a low engine speed.
> Switch on the tractor's PTO shaft.

> Adjust to 540 rpm.

> Lower the pick-up equipment via the control device.

Ground speed

Driving at a suitable ground speed ensures that the crop is collected

uniformly and constantly.

> Adapt the drive speed to the:

•

Quantity of crop,

•

Volume of the swaths,

•

The soil condition.

Driving pattern

The driving pattern is critical for the quality of the bale shape. Ensure

that the crop is picked up in a uniform manner. Where there are nar-

row swaths, do not swing backwards and forwards over the swath but

drive as shown in the diagram.

> Steer the implement so that the swath is guided into the pick-up

equipment alternately to the left and the right.

This ensures that the bale chamber is filled optimally.

> Check the filling process on a regular basis.

> When there is a visual or manual signal from the AutoPlus-Pilot-

box, the tying must be started manually or it starts automatically.

→

»Initiating tying«, page 77.

Initiating tying and

emptying the bale

chamber

All manuals and user guides at all-guides.com

all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды