Kverneland Vicon RF 2235 Скачать руководство пользователя страница 106

Страница: 106 / 135

106

Maintenance

Wheels

Do not drive with worn or damaged tyres

Replace worn or damaged tyres immediately. There is a high risk of

accident especially when driving on the road with such tyres.
Repair work

Repair work to wheels and tyres must be carried out:

•

by a specialist.

•

with the correct tools.

Specialised knowledge, specific tools and sound equipment are ne-

cessary to fit wheels and tyres. Personnel may be injured or the imple-

ment may be damaged as a result.
Prescribed tyre size

Only fit tyres which are the specified size. Fitting tyres of different si-

zes can cause accidents. Personnel may be injured or the implement

may be damaged as a result.
Prescribed tyre pressure

Only use tyres set at the prescribed tyre pressure. Incorrect tyre pres-

sures can result in serious damage to personnel or traffic accidents.
Securing the implement

Secure the implement against inadvertent starting and rolling away.

Use wheel chocks. The implement must be standing on firm and level

ground and, if necessary, must be supported during work. Unsecured

or non-supported implements can cause accidents. There is otherwi-

se the risk of serious or fatal injury.

Tightening the

wheel nuts

Tighten the wheel nuts:

•

After the first 250 bales.

•

At the start of the season.

•

After every tyre/wheel change.

Tighten the wheel nuts to 290 Nm.

All manuals and user guides at all-guides.com

all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды