Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 13 / 135

Safety

Who is allowed to

operate the

implement

Only qualified personnel

Only qualified persons who have been informed of the dangers asso-

ciated with handling the implement are permitted to operate, service

or repair the implement. This knowledge can be gained via agricultural

training, technical training or intensive instruction.

General

Safety is your responsibility

Follow the safety regulations. Ensure you are always in compliance

with the safety regulations. Most accidents can be avoided. Avoid se-

rious or fatal accidents by following the safety instructions.
Prescribed workwear

Do not wear loose, baggy clothing. Any loose or baggy items of clot-

hing worn may become caught in the rotating parts. Wear workwear

and protective clothing, as prescribed by the trade's mutual indemnity

association. There is otherwise the risk of serious or fatal injury.
Fire hazard

Ensure the implement is always clean and remove any remaining

crop. This will ensure that any fire hazards are avoided.
Fire extinguisher

The fire extinguisher must always be kept with the implement. A mul-

tipurpose ABC fire extinguisher with a volume of 5 kg is recommended.

The fire extinguisher must be approved by the relevant authorities.
Good working condition

Ensure that the tractor is always in good working condition, and that

the tractor's brakes and the implement are working perfectly. Observe

the information and technical data in the operating manual for your

tractor.
Use in enclosed spaces

An implement which is coupled and connected to the tractor must not

be run in enclosed spaces. Combustion engine exhaust fumes are

dangerous. There is a danger of asphyxiation.
Never work on the implement when it is running

Actions should not be carried out on the implement while it is running.

Objects or personnel can be caught, drawn in or crushed. There is

otherwise the risk of serious or fatal injury.
Do not make any modifications to the implement

No modifications whatsoever must be made to the implement. Unautho-

rised modifications can impair safety and affect the service life of the

implement. Unauthorised modifications to the implement render the

manufacturer's guarantee null and void and frees the manufacturer

from all liability.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды