Kverneland Vicon RF 2235 Скачать руководство пользователя страница 67

Страница: 67 / 135

Driving on the road

Emptying the bale

chamber.

Before road transport, the crop must be removed from the bale cham-

ber. Proceed as follows:
If bale production is not possible, remove the remaining crop from the

bale chamber.

> Carry out the »Cleaning the bale chamber« operating instructions,

page 81.

If bale production is possible, release the bale.

> Carry out the »“MANUAL/AUTO” program changeover« operating

instructions on page 67.

“MANUAL/AUTO”

program changeover

The following operating modes can be selected with the AutoPlus-Pi-

lotbox for net tying and twine tying:

•

AUTO: Automatic start of bale tying

•

MANUAL: Bale tying starts with the “GO” button

> The display shows automatic tying is active.

> Press the “MANUAL/AUTO” button:

> The display shows manual tying.

> Press the “GO” button. Net tying is triggered.

> The display shows “tying start” during bale wrapping.

> The display shows “rear flap open” after successful bale wrapping

and the cutting of the tying materials.

> Carry out the »Depositing the bale« operating instructions on page

79.

OTE

These operating instructions are also applicable for twine tying.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Бренды по названию

Популярные бренды