Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 84 / 135

Parking and storage

Safety

When setting down and parking the implement, special safety precau-

tions must be observed:
Observe safety instructions

Observe the safety instructions for the performance of all work. Any

disregard for safety instructions can lead to serious or fatal injuries to

persons.
The implement is not a toy

Children are forbidden from playing on or around the implement. The

parking area must be selected so that it is not immediately accessible

to unauthorised persons. Metal edges and work tools of the implement

can cause serious injury.

Uncoupling and

securing the

implement

Uncouple the implement in the reverse order to coupling.

> Stop the implement on dry, firm and level ground.

> secure the tractor in such a way that it cannot roll forwards or back-

wards.

> Disconnect the hydraulic couplings and secure the drawbar in the

transport holder.

> Disconnect the lighting plug and insert it into the transport holder

for connections on the drawbar.

> Disconnect the AutoPlus-Pilotbox plug and insert it into the trans-

port holder.

> Store the twine box in the AutoPlus-Pilotbox.

> Lower the sustainer.

→

Reverse sequence of the »Raising the sustainer«, page 38.

> Remove the safety splint from the bolt.

> Remove the bolt from the sustainer.

> Lower the sustainer and secure with bolts and safety splints.

> Secure the implement with wheel chocks.

Crank

Sustainer

Transport holder

for connections

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды