Kverneland Vicon RF 2235 Скачать руководство пользователя

Страница: 49 / 135

Preparing for use

Adjusting the

OptiCut cutterbar

Wear protective gloves

The knives are very sharp. Always wear protective gloves when hand-

ling the knives. Failing to wear protective gloves can cause serious in-

juries.
Secure the control devices

Secure the control devices on the tractor against unintended actuation

and lock if possible. Unintended actuation of the control device can cau-

se the implement to move unexpectedly and may cause accidents.
Working in the bale chamber

The following conditions must be observed for carrying out repairs and

maintenance work and rectifying malfunctions in the bale chamber:

> Empty and open the bale chamber.

> Switch off the tractor's PTO shaft.

> Switch off the tractor engine.

> Switch off the AutoPlus-Pilotbox.

> Take out the ignition key.

> Secure the bale chamber with the ball valve.

Severe accidents can result if the device starts inadvertently.

OptiCut cutterbars

Cutterbar

Knife protection

OptiCut 14

Mechanical

OptiCut 23 SuperSilage

Mechanical

OptiCut 23 HydroProtected

Hydraulic

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды