Kverneland Vicon RF 2235 Скачать руководство пользователя страница 20

Страница: 20 / 135

Safety

Unhitching

Increased risk of injury

There is an increased risk of injury when uncoupling the implement

from the tractor. Therefore:

•

Secure the tractor against rolling away, switch off and take out the

ignition key.

•

Never stand between the tractor and the implement during uncou-

pling.

•

Stop the implement on firm, secure, level ground.

•

Ensure that the sustainer is securely locked.

•

Place the cardan shaft in the brackets provided.

•

Secure the implement against rolling away (use wheel wedges).

•

Do not disconnect the hydraulic tubes until the hydraulic system is

at zero pressure on both the tractor and implement faces.

If this is not complied with, the consequence can be serious or fatal

injuries.

All manuals and user guides at all-guides.com

Содержание Vicon RF 2235








































































































































Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды

Kverneland Vicon RF 2235, Руководство по эксплуатации

Результаты поиска

Содержание Vicon RF 2235

Отзывы:

Похожие инструкции для Vicon RF 2235

Бренды по названию

Популярные бренды