Kohler Comand Pro CH1000 Скачать руководство пользователя страница 95

Страница: 95 / 142

8.15

Section 8

Disassembly

Remove Governor Yoke, Cross Shaft, and
Seal

1. Remove the two mounting screws securing the

yoke to the governor cross sha

. See Figure 8-61.

Figure 8-61. Removing Cross Shaft/Yoke Screws.

2. Pull the governor cross sha

out of the crankcase

and remove the seal.

Remove Lifter Feed Chamber Cover and
Gaskets

1. Remove the three screws securing the li

er feed

chamber ba

ﬄ

e (some models only), cover, and

gaskets. Carefully separate the parts from the
crankcase. See Figure 8-62.

Baffl e (Some

Baffl e (Some
Models Only)

Models Only)

Gasket

Cover

Screws

Figure 8-62. Removing Lifter Feed Chamber Cover
Components.

Remove Flywheel and PTO End Oil Seals

1. Remove the oil seals from the crankcase and

closure plate using a seal puller. See Figure 8-63.

Figure 8-63. Removing Oil Seals.

Removal of Main Bearings

NOTE: Flywheel and PTO side main bearings

should only be removed if replacement
is required due to wear. If removal is
performed, use a press and support the
casting surface around the bearing

ange.

not

press against or support by the gasket/

outer perimeter surface. See Figure 8-64.

Support
This Surface

Figure 8-64. Support Surface Details.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды