Kohler Comand Pro CH1000 Скачать руководство пользователя страница 67

Страница: 67 / 142

7.15

Section 7

Electrical System and Components

Stator

The stator is mounted on the crankcase behind
the

ywheel. Follow the procedures in Section 9 -

Disassembly

and Section 11 -

Reassembly

if stator

replacement is necessary.

Rectifi er-Regulator

The recti

er-regulator is mounted on the backing

shroud assembly. See Figure 7-16. To replace it,
disconnect the plug, remove the two mounting
screws, and ground lead.

NOTE: When installing the recti

er-regulator, take

note of the terminal positions and install the
plug correctly.

Ground
Lead

Connector Plug

Rectifi er-
Regulator

Figure 7-16. Rectifi er-Regulator.

Testing of the recti

er-regulator may be performed as

follows, using the appropriate Recti

er-Regulator

Tester (see Section 2).

To Test –

NOTE: Disconnect all electrical connections a

ached

to the recti

er-regulator. Testing may be

performed with the recti

er-regulator

mounted or loose. The

gures show the part

removed from the engine for clarity. Repeat
the applicable test procedure

two or three

times

to determine the condition of the part.

20/25 Amp Rectifi er-Regulators

1. Connect the single lead adapter in between the

B+ (center) terminal of recti

er-regulator being

tested and the squared single end of the tandem
adapter lead. See Figure 7-17.

Figure 7-17. Connected Adapter.

2. Connect the tester ground lead (with spring

clamp) to the body of the recti

er-regulator.

3. Connect the red lead and one of the black leads

to the pair of terminals on the open end of
the tandem adapter lead (connections are not
location speci

c).

4. Connect the remaining black lead from the tester

to one of the outer AC terminals on the recti

er-

regulator. See Figure 7-18.

Figure 7-18. Connected Tester.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды