Kohler Comand Pro CH1000 Скачать руководство пользователя страница 133

Страница: 133 / 142

10.23

Section 10

Reassembly

Valley Baffl e

Figure 10-90. Installing Valley Baffl es.

Install Carburetor

WARNING: Explosive Fuel!

Gasoline may be present in the carburetor and fuel system.
Gasoline is extremely

ammable and its vapors can explode

if ignited. Keep sparks and other sources of ignition away
from the engine.

1. Install a new carburetor gasket onto the intake

manifold with the tab

. Make sure all holes

align and are open.

2. A

ach the choke return spring and bracket to the

front hole in the choke lever on carburetor. See
Figure 10-91.

Choke Return Spring and Bracket

Choke

Choke
Lever

Lever

Figure 10-91. Choke Return Spring and Bracket
Details.

3. Connect the thro

le and choke linkages to the

carburetor if they were previously disconnected.
Install the carburetor with the linkages a

ached

as an assembly. See Figure 10-92.

Gasket
(Tab Up)

Throttle

Throttle
Linkage

Linkage

Choke

Choke
Linkage

Linkage

Carburetor

Figure 10-92. Installing Carburetor with Linkages.

4. Connect the fuel line to the carburetor inlet and

secure with a clamp.

Install Governor Lever

1. Install the governor lever onto the governor sha

and connect the thro

le linkage with the black

clip. Do not tighten the governor lever at this
time. See Figure 10-93.

Governor
Lever

Throttle Linkage
and Black Clip

Figure 10-93. Installing Governor Lever.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды