Kohler Comand Pro CH1000 Скачать руководство пользователя страница 112

Страница: 112 / 142

10.2

Section 10
Reassembly

Mounting
Screws

Baffl e (Used on Some
Models Only)

Cover

Gasket

Lifter
Feed
Chamber

Figure 10-4. Lifter Feed Chamber Assembly
Details.

Install Flywheel End Main Bearing

If the

ywheel end main bearing was removed in

servicing, install a new bearing using an arbor press
and driver.

1. Make sure the crankcase bore for the main

bearing is clean, dry and free of nicks or burrs.

2. Press the

ywheel side main bearing in place

with the notch oriented in the 12 o’clock position
using an arbor press and driver. See Figure 10-5.
Make sure the bearing is fully seated against
the

ange and the oil feed hole is open in the

crankcase. See Figure 10-6.

3. Apply a light coat of clean engine oil to the inner

surface of the main bearing.

Figure 10-5. Installing Main Bearing.

2. Apply a light coat of clean engine oil to the

outside diameter of the oil seal.

3. Install the oil seal into the crankcase using a seal

driver. Make sure the oil seal is installed straight
and true in the bore and that the tool bo

oms

against the crankcase. See Figures 10-2 and 10-3.

Figure 10-2. Installing Oil Seal with Driver.

Figure 10-3. Installed Flywheel End Oil Seal.

Install Lifter Feed Chamber Gaskets and
Cover

1. Install the li

er feed chamber gasket, followed by

the li

er feed cover over the li

er feed chamber.

If used, position the breather ba

ﬄ

e on top of the

parts with the winged o

ﬀ

set down.

2. Install the three screws. Make sure all the parts

are properly aligned.

Torque the screws to

6.2 N·m (55 in. lb.)

into new holes, or

4.0 N·m

(35 in. lb.)

, into used holes. See Figure 10-4.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды