Kohler Comand Pro CH1000 Скачать руководство пользователя страница 70

Страница: 70 / 142

7.18

Section 7
Electrical System and Components

DC Voltmeter

Rectifi er-Regulator

Flywheel
Stator

Ammeter

Battery

(-)

(+)

Electric Starting Motors

The engines in this series use solenoid shi

starters. A

Delco-Remy solenoid shi

starter is typically used.

Starting Motor Precautions

NOTE: Do not crank the engine continuously for

more than 10 seconds at a time. If the engine
does not start, allow a 60 second cool-down
period between starting a

empts. Failure

to follow these guidelines can burn out the
starter motor.

NOTE: If the engine develops su

ﬃ

cient speed to

disengage the starter but does not keep
running (a false start), the engine rotation
must be allowed to come to a complete stop
before a

empting to restart the engine. If

the starter is engaged while the

ywheel is

rotating, the starter pinion and

ywheel ring

gear may clash, resulting in damage to the
starter.

NOTE: If the starter does not crank the engine, shut

ﬀ

the starter immediately. Do not make

further a

empts to start the engine until the

condition is corrected.

NOTE: Do not drop the starter or strike the starter

frame. Doing so can damage the starter.

Starter Removal and Installation

Refer to the Disassembly and Reassembly Sections for
starter removal and installation procedures.

Operation – Solenoid Shift Starter

When power is applied to the starter the electric
solenoid moves the drive pinion out onto the drive
sha

and into mesh with the

ywheel ring gear. When

the pinion reaches the end of the drive sha

it rotates

the

ywheel and cranks the engine.

When the engine starts and the start switch is released
the starter solenoid is deactivated, the drive lever
moves back, and the drive pinion moves out of mesh
with the ring gear into the retracted position.

Figure 7-22. Connections for Testing Charging System.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды