Kohler Comand Pro CH1000 Скачать руководство пользователя страница 94

Страница: 94 / 142

8.14

Section 8
Disassembly

Figure 8-57. Remove Connecting Rod Caps.

NOTE: The cylinders are numbered on the crankcase.

Use the numbers to mark each end cap,
connecting rod and piston for reassembly.

not

mix end caps and connecting rods.

2. Carefully remove the connecting rod and piston

assembly from the cylinder bore. See Figure 8-58.

Figure 8-58. Removing Piston/Connecting Rod
Assemblies.

3. Repeat the above procedures for the other

connecting rod and piston assembly.

Remove Crankshaft

1. Carefully pull the cranksha

from the crankcase.

See Figure 8-59. Note thrust washers and shims if
used.

Figure 8-59. Removing Crankshaft.

Removal of Governor Gear Assembly

The governor gear is held onto the sha

by small

molded tabs in the gear. When the gear is removed
from the sha

, these tabs are destroyed and the gear

must

be replaced. Therefore, remove the gear

only

if absolutely necessary. If the governor cross sha

yoke, or gear condition does not require removal,
the governor gear may be le

in place. If removal is

necessary, perform as follows:

1. Remove the locking tab thrust washer and note

orientation.

2. Using a screwdriver, carefully pry upward to

unseat the governor gear assembly from the
governor gear sha

. Remove the regulating pin

and governor gear assembly. See Figure 8-60.

Governor Gear

Figure 8-60. Removing Governor Gear.

3. Inspect the governor gear sha

for wear or

damage. Remove the sha

only if replacement is

needed.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды