Kohler Comand Pro CH1000 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 142

background image

8.1

Section 8

Disassembly

8

Section 8

Disassembly

WARNING: Accidental Starts!

Disabling engine. Accidental starting can cause severe injury or death.

Before working on the engine or equipment,

disable the engine as follows: 1) Disconnect the spark plug lead(s). 2) Disconnect negative (-) ba

tt

ery cable from ba

tt

ery.

General

Clean all parts thoroughly as the engine is
disassembled. Only clean parts can be accurately
inspected and gauged for wear or damage. There
are many commercially available cleaners that will
quickly remove grease, oil and grime from engine
parts. When such a cleaner is used, follow the
manufacturer’s instructions and safety precautions
carefully.

Make sure all traces of the cleaner are removed before
the engine is reassembled and placed into operation.
Even small amounts of these cleaners can quickly
break down the lubricating properties of engine oil.

Typical Disassembly Sequence

The following sequence is suggested for complete
engine disassembly. The sequence can be varied to
accommodate options or special equipment.

1. Disconnect spark plug leads.
2. Shut o

ﬀ

fuel supply.

3. Drain oil from crankcase and remove oil

fi

lter.

4. Remove mu

ﬄ

er.

  5.  Remove cylinder shrouds and blower housing.
  6.  Remove electric starter motor.
  7.  Remove air cleaner assembly.
  8.  Remove control bracket, governor springs, and

lever.

9.  Remove carburetor.
10.  Remove Oil Sentry™ (if equipped).
11.  Remove  ba

ﬄ

es and intake manifold.

12. Remove oil cooler.
13. Remove

oil

fi

lter housing and oil

fi

lter adapter.

14. Remove ignition modules.
15. Remove grass screen and cooling fan
16. Remove

fl

ywheel.

17. Remove stator, recti

fi

er-regulator, and wiring

harness.

18. Remove backing shroud assembly.
19. Remove spark plugs.

20. Remove valve covers and fuel pump.
21. Remove cylinder heads and hydraulic li

ft

ers.

22.  Disassemble cylinder heads.
23.  Remove breather assembly.
24.  Remove oil reservoir and pickup screen.
25.  Remove closure plate assembly.
26.  Remove  camsha

ft

.

27. Remove connecting rods with pistons and rings.
28. Remove cranksha

ft

.

29. Removal of governor gear assembly.
30. Remove governor yoke, cross sha

ft

, and seal.

31. Remove li

ft

er feed cover and gaskets.

32. Remove

fl

ywheel and PTO end oil seals.

33. Removal of main bearings.

Disconnect Spark Plug Leads

1. Disconnect the leads from the spark plugs. See

Figure 8-1.

NOTE: Pull on boot only, to prevent damage to spark

plug lead.

Figure 8-1. Disconnect Both Spark Plug Leads.

«
...
79
80
81
82
83
...
»

Содержание Comand Pro CH1000















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Comand Pro CH1000

Бренд: Stihl Страницы: 40

Бренд: Westerbeke Страницы: 140

Бренд: Interpump Страницы: 16

Бренд: Volvo Penta Страницы: 90

Бренд: Volvo Penta Страницы: 108

Бренд: Volvo Penta Страницы: 61

Бренд: Volvo Penta Страницы: 92

Бренд: Volvo Penta Страницы: 216

Бренд: Volvo Penta Страницы: 164

Бренд: Hino Motors Страницы: 339

Бренд: YS Страницы: 2

Бренд: GPOWER Страницы: 4

Бренд: LONCIN Страницы: 23

Бренд: DLE Страницы: 24

Бренд: Toyota Страницы: 222

Бренд: Mitsubishi Страницы: 216

Бренд: Ford Страницы: 42

Бренд: DAF Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды