Kohler Comand Pro CH1000 Скачать руководство пользователя страница 129

Страница: 129 / 142

10.19

Section 10

Reassembly

Ground
Lead

Connector
Plug

Rectifi er-
Regulator

Figure 10-76. Installing Rectifi er-Regulator and
Ground Lead.

Install Flywheel

WARNING: Damaging Crankshaft and
Flywheel Can Cause Personal Injury!

Using improper procedures to install the

ywheel can crack

or damage the cranksha

and/or

ywheel. This not only

causes extensive engine damage, but can also cause personal
injury, since broken fragments could be thrown from the
engine. Always observe and use the following precautions
and procedures when installing the

ywheel.

NOTE: Before installing the

ywheel make sure

the cranksha

taper and the

ywheel hub

are clean, dry, and completely free of any
lubricants. The presence of lubricants can
cause the

ywheel to be over stressed and

damaged when the hex

ange screw is

torqued to speci

cations. See Figures 10-77

and 10-78.

Figure 10-77. Clean and Dry Taper of Crankshaft.

Figure 10-78. Clean and Dry Flywheel Hub.

NOTE: Make sure the

ywheel key is installed

properly in the keyway. The

ywheel can

become cracked or damaged if the key is not
properly installed. See Figure 10-79.

Figure 10-79. Installed Flywheel Key.

1. Install the woodru

ﬀ

key into the keyway of the

cranksha

. Make sure that the key is properly

seated and parallel with the sha

taper.

2. Install the

ywheel onto the cranksha

, being

careful not to shi

the woodru

ﬀ

key.

3. Install the hex

ange screw and washer.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды