Kohler Comand Pro CH1000 Скачать руководство пользователя страница 109

Страница: 109 / 142

Section 9

Inspection and Reconditioning

9.13

4. Install the O-ring in the groove of the oil pump

housing. Use a small quantity of grease to hold it
in place. See Figure 9-16.

O-ring

Figure 9-16. O-ring Installed in Oil Pump Housing.

5. Lightly lubricate the I.D. of the inlet seal with

oil and carefully insert the ferruled end of the
pickup tube through the grommet, into the oil
pump housing. Position the pickup tube so the
outboard end faces up. See Figure 9-17.

6. Install the oil pump housing with the pickup

tube, over the oil pump boss and gears. Position
the relief valve ba

ﬄ

e on screws 2 and 3. See

Figure 9-18. Align the three screw hole locations.

Relief
Valve
Baffl e

Oil
Pump

Pickup
Tube

Pickup
Tube
Clamp
and
Screw

Mounting
Screws

Figure 9-17. Installed Oil Pump and Pickup Tube.

7. Install the clamp for the pickup tube and

nger

tighten the screw. Check the alignment of the
parts and torque the oil pump housing screws
as speci

ed using the sequence shown in Figure

9-18.

Torque

the

hex

ange screws as follows:

a. Install fastener into location No. 1 and lightly

tighten to position the pump.

b. Install fastener into location No. 2 and fully

torque to the recommended value.

c. Install fastener into location No. 3 and fully

torque to the recommended value.

d. Finish torquing fastener in location No. 1 to

the recommended value.

First

Time

Installation:

10.7 N·m (95 in. lb.)

All

Reinstallations:

6.7 N·m (60 in. lb.)

Figure 9-18. Oil Pump Screws Torque Sequence.

8. Torque the clamp (pickup tube) mounting

screw to

10.7 N·m (95 in. lb.)

into a new hole, or

7.3 N·m (65 in. lb.

) into a used hole. See Figure

9-17.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды